Originally created to imitate a vintage look (as observed on classic violins) Sunburst really is a fantastic guitar finish frequently encountered upon guitars antique and modern. It's an extremely popular guitar finish but is it too difficult for the average person?
It's possible to achieve a sunburst finish for your guitar if you comply with just a few steps and take great care. It's prudent to experiment initially by using a discarded bit of timber prior to trying your hand on the electric guitar.
If it's a brand new guitar kit,you should construct the actual guitar to start with. As expected you will end up deconstructing to begin the finish nevertheless, you need to know that you will not berunning into problems with the final build that endanger the finish you've undoubtedly put a huge amount of effort towards.
When you've put together the electric guitar and checked for potential issues you can begin to prep the timber. Sand right back until eventually you've got a totally even surface to work with. At that point get rid of unwanted debris and tidy the guitar extensively.
Following that apply plenty of timber grain filler. Make sure you put on heavily across the face belonging to the guitar and afterwards work it in. Once dried remove the excess and remove excess with a moistened rag. Now it is time for you to paint the back and sides of the body and neck of your electric guitar. A key factor to take into account is to always conceal the body and neck.
As you are spraying paint or lacquer it's wise to keeping your aerosols in quite warm water before using. It's going to take a combination of coats for this reason you shouldn't try to apply too much all at one time. The trick will be to build up the tone layer after layer and apply from a fair distance away so that you can accomplish a gentle edge. The closer you get the more complicated the edge line you will end up with.
Next apply the amber lacquer. Chances are you'll be obliged to cover the sides that belong to the guitar and then place the guitar on the strong work bench face up before you apply. Once you have finished this step you can apply the clear coat next and sand between coats to get rid of any runs. Then apply the next darkest stain to achieve a blend of colouring within the edge and inner colours. Consider applying very thin and build up the obligatory coats. About now it's best to let the most recent coat harden off. When the guitar is completely free of moisture begin the process of sanding for a second time.
This really is a final detail. The key here is to use a lighter measure of sand paper every single time you end up being basically taking out the marks from the gauge of sandpaper applied preceding and then progressing which has a finer gauge. Keep delicately sanding and then changing to a finer gauge unless you run out of sandpaper after which you can move on to your buffer.From this point you may just continue to keep buffing or hand polishing until you end up getting completely happy with the finished look.
It's possible to achieve a sunburst finish for your guitar if you comply with just a few steps and take great care. It's prudent to experiment initially by using a discarded bit of timber prior to trying your hand on the electric guitar.
If it's a brand new guitar kit,you should construct the actual guitar to start with. As expected you will end up deconstructing to begin the finish nevertheless, you need to know that you will not berunning into problems with the final build that endanger the finish you've undoubtedly put a huge amount of effort towards.
When you've put together the electric guitar and checked for potential issues you can begin to prep the timber. Sand right back until eventually you've got a totally even surface to work with. At that point get rid of unwanted debris and tidy the guitar extensively.
Following that apply plenty of timber grain filler. Make sure you put on heavily across the face belonging to the guitar and afterwards work it in. Once dried remove the excess and remove excess with a moistened rag. Now it is time for you to paint the back and sides of the body and neck of your electric guitar. A key factor to take into account is to always conceal the body and neck.
As you are spraying paint or lacquer it's wise to keeping your aerosols in quite warm water before using. It's going to take a combination of coats for this reason you shouldn't try to apply too much all at one time. The trick will be to build up the tone layer after layer and apply from a fair distance away so that you can accomplish a gentle edge. The closer you get the more complicated the edge line you will end up with.
Next apply the amber lacquer. Chances are you'll be obliged to cover the sides that belong to the guitar and then place the guitar on the strong work bench face up before you apply. Once you have finished this step you can apply the clear coat next and sand between coats to get rid of any runs. Then apply the next darkest stain to achieve a blend of colouring within the edge and inner colours. Consider applying very thin and build up the obligatory coats. About now it's best to let the most recent coat harden off. When the guitar is completely free of moisture begin the process of sanding for a second time.
This really is a final detail. The key here is to use a lighter measure of sand paper every single time you end up being basically taking out the marks from the gauge of sandpaper applied preceding and then progressing which has a finer gauge. Keep delicately sanding and then changing to a finer gauge unless you run out of sandpaper after which you can move on to your buffer.From this point you may just continue to keep buffing or hand polishing until you end up getting completely happy with the finished look.
About the Author:
Guitar Kits are a great way to get yourself started making guitars. For great tips and resources for Guitar Kits, stop by eguitarkits.com.
